NO ACTIVE PARTITION FOUND WINDOWS

At this point start over on another t620 is not an option. I believe there is a critical flaw with this model and HP has been unable to provide me with any solution.

I need this to be resolved as I have wasted too much time building images that can't be captured. Tried several flash drives again with same result. However, When I tried to make another copy to have as a back up I received the same dreaded error ***ERROR*** There is no active partition on disk 0! So if I need to make any changes I will not be able to capture that image to deploy. Even when I completed configuring the apps and updates we needed I successfully captured an image. Out of the box I was able to capture the image.

So I took out another new t620 from the box and started rebuilding and testing a new image. I was told by HP support that this was a corrupt drive on the thin client and to ship it back to them. ***ERROR*** There is no active partition on disk 0! I tried 5 different flash drives and had the same result. When using the thin state tool to capture the image to a flash drive I get the following error.

NO ACTIVE PARTITION FOUND WINDOWS

If the partition was not formatted by using Windows, you might also need to run the Recovery Console fixboot command to make the active partition bootable.ДЄfter you can boot into Windows, it is recommended that you use the Windows Disk Management snap-in tool to reset the original system partition as the active partition, and then restart the computer.I set up a new t620 thin client using the window 8 OS that it ships with. There is a space between the d and the two periods (.). Start your computer by using the Windows XP Setup floppy disks or by using the Windows XP CD-ROM.ДЄt the Welcome to Setup screen, press F10, or press R to repair.Д¬opy the Ntldr file from the Windows XP CD-ROM to the root of your system partition by using the following commands, pressing ENTER after each command: Using the Recovery Console, copy the Ntldr file from the Windows XP CD-ROM to the root directory of the current active partition. On Intel x86 computers, this is always drive 0, the drive that the system BIOS searches when the operating system starts. On Intel x86-based computers, the system partition must be a primary partition that is marked active. The system partition refers to the disk volume that contains the files that are needed to start Windows (for example, Ntldr, Boot.ini, and ). If the partition that has been incorrectly marked as active is formatted in the FAT file system, the FAT32 file system, or the NTFS file system, you may be able to use the Windows Recovery Console to correct the behavior.ДЇor more information, see What are the system recovery options in Windows?. For more information, see Create a system repair disc.

Remove the boot floppy disk, and then restart the computer.Д«oot the computer by using a Windows XP boot disk.Click Set active partition, press the number of the partition that you want to make active, and then press ENTER.When you are prompted to enable large disk support, click Yes.At the command prompt, type fdisk, and then press ENTER.Boot to a command prompt by using a Microsoft Windows 95, Microsoft Windows 98, or Microsoft Windows Millennium Edition (Me) boot floppy disk.Try changing the active partition by booting to a floppy disk and then using disk utilities to manually change the active partition: To resolve this behavior, use one of the following procedures: ResolutionД«efore performing the steps listed below, make sure that you have a good backup of your critical data files. If you want to use another operating system, you must first mark its system partition as active before restarting the computer. There can be only one active system partition at a time. This partition must be located on the disk that the computer gains access to at startup. On Intel-based computers, the system partition must be a primary partition that has been marked as active for startup purposes. This behavior occurs if the partition marked as active does not contain the Windows boot files or the boot files for another operating system. This article provides a solution to an issue where the computer doesn't start after you mark your primary partition as active.ДЄpplies to: Windows Server 2012 R2 Original KB number: 315261 SymptomsДЄfter you use the Windows Disk Management snap-in tool to mark your primary partition as active, the computer may not start, and you may receive the following error message:

No active partition found